MicroNet SP5012A Uživatelský manuál

User’s Manual IP Telephony Gateway, FXS + FXO Interface Model No.: SP5012/S, SP5014/S Website: http://www.micronet.info

transmitted received. Back panel: SP5012/S SP5014/S 1. Ethernet Port LAN/WAN: 10/100 Base-T; RJ-45 socket, complied with ETHERNET 10/100base-T

PINOUTS Pin Name Dir Description 2 RXD Receive Data 3 TXD Transmit Data 5 GND System Ground 3. TEL: RJ-11 connector, FXS interface is for connect

2 How to Setup and Connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or C

Figure 2.1: Network Configuration 3 Select the Property of the LAN card. 4 Setup the ip address, subnet mask and default gateway as below: Figure 2

2.3 Network configurations in your gateway 1 Key in the ip address of the gateway (http://10.1.1.3) with the browser. (see figure 2.3) Figure 2.3:

3 You will enter the main page of the configuration after key in the login name and password correctly: (see figure 2.5) Figure 2.5: The main WEB con

2.3.1 Static IP address 1 Please get the correct IP address, netmask and default gateway address from your ISP first. Press the OK button if you fin

3 Press the reboot if you want the configuration executed. (see figure 2.9) Figure 2.9: Reboot the system 17

2.3.2 DHCP mode 1 Enable the DHCP if you are using the cable modem or DHCP server. (see figure 2.10) Figure 2.10: Enable the DHCP function 2 Please

2.3.3 PPPoE mode 1 Switch to the PPPoE mode and press the “OK” button. Press the Network Interface button after the “OK” button. (see figure 2.11) F

Steps in configuration To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully bef

2 Please commit the data and reboot the machine after you finished the configuration about the PPPoE function. 20

2.4 Making a VoIP Call There are two modes that you could configure the gateway for making VoIP calls. One is the Peer-to-Peer mode, another is Prox

Figure 2.14: Phone Book 【Example】 Figure 2.15: The example of Phone Book configuration The name of the destination: test The E164 number (phone

The call signal port of the destination: 1720 (The port will be 1720 if you don’ t define it) Drop prefix: Enable – The e164 number you define wil

【The application in the drop and insert function】 Input (E164) Drop Insert Output 100 Disable X 100 200 Disable 0 0200 300 Enable X X 400 En

configuration. 3 Switch to the Security Config page and put the user account and password in the correct table. Please get this info from your ITSP.

3 Advanced There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Please get the inf

be forwarded to the number you configured. This is only for the E164 number or the phone numbers you want to transfer. This function should be used

3.2 System Configuration There are some parameters in the system configurations, please get more detail as following. (see figure 3.2) Figure 3.2:

3.3 Voice Setting User could define some parameters about the voice in this voice-setting page. (see figure 3.3) Figure 3.3: Voice Setting ● Codec

Table of Contents 1 START UP ...

A large jitter buffer causes increase in the delay and decreases the packet loss. A small jitter buffer decreases the delay but increases the packet

3.5 Tone Setting The Tone Setting is for the Tone detecting. The call will be dropped if the pattern of the tone from PSTN side is as same as the pat

3.6 Prefix The Prefix function is using the drop and insert function (see figure 3.6). Figure 3.6: Prefix Configuration There is a rule between Pr

There is an example about the configuration, please follow up these steps. 1 Press the Prefix Configuration button to enter the configuration table

3 Press the Prefix Configuration button to reload the configuration table (see figure 3.8) Figure 3.8: Show the added table 4 Please Commit it and R

3.7 Routing Table Routing Table is a rule to define the destination of the calls you make. You could define the rules by the number you dial or by th

Change the default routing Please follow up the steps if you want to change the default routing: 1 Pick up the side for the incoming calls and defi

2 The default setting is changed after you press the Change Default button. Please press the Routing Table button again to show the new setting. (see

Add a new Routing Table 1 The default setting is changed after you press the Change Default button. Please press the Routing Table button again to sh

this routing if the number I dial is between 1 and 10 digits. If I dial over 10 digits, this call will follow the default routing. ● Hunt – Define

5.10 [SYSCONF]... 54 5.11 [SIP]...

3.8 FXO Password You will get the IVR if you make calls from PSTN side. The IVR will ask you the password you set, and you could make other calls to

3.9 Password There are two accounts for login to access or change the configurations. One is “root”, another is “administrator”. Users could define t

3.10 Upgrade the Firmware User could update the firmware just by the web configuration interface. There are two types for the upgrading procedure. On

2 Key in the IP address, the login name, password of your FTP server and the correct file name. (see figure 3.17) Figure 3.17: FTP information Ple

switch to the TFTP method. (see figure 3.18) Figure 3.18: ROM Upgrade for TFTP 3 Key in the IP address of your TFTP server, pick up the file type fo

6 After pressing the “Flash Clean” button, please press the “Reboot System” button to make it reboot. 45

4 Console Setup 4.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal emu

Figure 4.3: Pick up the right interface to use 4. Configure the COM Port Properties as following: ● Bits per second: 9600 ● Flow control: None

5 Command List 5.1 [help] Type help or man or ? to list all the available command. usr/config$ help help help/man/? [command] quit quit/exit/clo

5.2 [quit] Type quit will quit the Gateway configuration mode and turn back to login prompt (in console mode) or disconnect (in TELNET mode). usr/con

1 Start Up 1.1 Introduction Micronet SP5012/S,SP5014/S is a multi-port FXS+FXO gateway. It supports an innovative intelligent call routing function t

5.4 [reboot] After commit command, type reboot to reload Gateway in new configuration. The procedure is as below: usr/config$ reboot .Attached TCP/I

Warning: Only user who login with root can execute this command. Configurations of IP address and accounts’ passwords will be kept. 5.6 [commit]

address. -ipchange Replace IP address if the shared IP is changed. -cmcenter Specify IP address of management center. Note: SNTP mode (

dynamic IP Address is not working in Peer-to-Peer mode. --------------------------------------------------------------------------------------------

PING 192.168.1.254: 56 data bytes 64 bytes from 192.168.1.254: icmp_seq=0. time=5. ms 64 bytes from 192.168.1.254: icmp_seq=1. time=0. ms 64 bytes f

-eod End of dial.(Enable: 1 / Disable : 0) Example: sysconf -ring 500 usr/config$ Parameters Usage: -print print out all current settin

Type, Gateway may be not functional if set wrong hardware type. -ring ring time for ring detection (in ms). When Gateway has incoming call from PST

-expire The relative time after which the message expires (0~65535). -port SIP local UDP port number (5060~5070). Default :

-expire It just like the TTL function in H323, the gateway will make sure the registration is success or not for a period times. -port define the

5.13 [line] This command is for configure each line parameters of Gateway. --------------------------------------------------------------------------

1.2 Features and specification Features ● IETF RFC 3261 ● Automatically Dial Path Selection (IP or PSTN) ● PSTN Line switch to telephone set whe

Proxy or P2P mode. (1) Call out from FXS Line Proxy Mode Usage: Set gateway under proxy mode. Create a Hotline table with “line ” command. -------

------------------------------------------------------------------------------- usr/config$ pbook –add name micronet ip 10.1.1.1 e164 1001 usr/config

[min number][max number][hunt number] route -ip [dst number][SIP number] route -fxs [dst number][SIP number] route -fxo [dst number][SIP num

-fxs create routing table for incoming call from FXS TELs. (route –fxs dst “destination port type” e164 “SIP number of port”) -fxo create routing

determine. (Ex. route –fxs dst 2) (2) If user doesn’t want to determine a specific port to route, SIP number must set as “x”. (Ex. route –ip dst 1 e1

(prefix –delete prefix “prefix number”) -modify modify a rule to drop or insert prefix digits of incoming call. (prefix –modify prefix “prefix numbe

Example: pbook -add name test e164 1234 ip 192.168.1.10 drop 1 insert 5678 pbook -delete 1 pbook -modify 1 name test e164 5678 ip 192.168.1

5.17 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by Gateway. ----------------

voice volume (0~63, default: 29,28), input gain (0~63, default: 26), dtmf volume (0~31, default: 23),

G.723.1. If the version is 2sipfxso723.100, SP5014/S doesn’t have the codec G.729 series. (2) For SP5012/S, the Application rom has the only one vers

FXO Features ● 2-wire loop start ● Support auto-attendant (Tone or voice greeting) ● PSTN polarity reversal detection ● Provide 2nd dial tone to P

usr/config$ phone Phone ringing , ringback tone , busy tone , dial tone setting and notes Usage: phone [-ring [freq ][ringON ][ringOFF ][ringLev

phone -rbt 480 440 8 8 2000 4000 2000 4000 phone -bt 620 480 8 8 500 500 500 500 phone -dt 440 350 8 8 500 1023 1023 1023 pho

-dt to set DialTone value. The played tone type, when hook off a phone set of workable Gateway. -flash set the detective flash range in ms, f

PSTN network. (If user doesn’t know about the frequency of disconnect tone or ring back tone, please refer to [record] command to detect frequency.)

passwd password 5.21 [record] User can record greeting and askpin file and analyze tone frequency by calling in FXO line of Gateway. --------

Press (S) to stop record... ... ...

Press (S) to stop record... ... ...

Press (R) to start record... r ... ...

4. Pease dial the number of the Tel 1 port. 5. The phone will ring if the number you dial is correct. 6. Pick up the phone and make sure the call

tone –print Disconnect tone 1 parameter Frequency high : 620 frequency low : 480 frequency high level : 8 frequen

1.3 Accessories and equipment ● The voice gateway in 2 FXS and 2 FXO ports or 1 FXS port and 1 FXO port models and two RJ-45 connector (WAN and LA

Tone2 off : 50 (Confirm the values is correct or not) (Key in the commit and reboot command if you finish the procedures as above) 【

Disconnect tone 2 parameter Frequency high : 450 frequency low : 0 frequency high level : 8 frequency low level

RTP payload type configuration and information Usage: pt-print Display the RTP payload type information -rfc2833 Configure the DTMF

-askpin update ask pin code voice file(optional) -s IP address of TFTP/FTP server (mandatory) -f file name(mandatory)

usr/config$ passwd Password setting information and configuration Usage: passwd -set Loginname Password passwd -clean Note: 1. Loginname

1.4 Appearance Front panel: The LED lights provide related system messages of the gateway. SP5012/S SP5014/S Power: Light on means Gateway is